Showing 61–80 of 95 results

Stud AN – Magazined Nails for Powder Actuated Tool

The AN stud is suitable for the permanent and temporary fixing of fasteners in... more

The AN stud is suitable for the permanent and temporary fixing of fasteners in structural steel, concrete, solid brick and solid lime-sand brick. Studs in magazines can only be used in stud drivers having a suitable magazine.

The smooth shaft of the AN Stud is built from high-strength steel, mechanically galvanised (minimum surface thickness 8 μm) and with ballistic tip. It can be used for Stud Driver AM 60.

.

Sales units: 200 pcs

Stud AN – Nail for Powder Actuated Tool

The smooth shaft of the Stud AN is built from high-strength steel, mechanically... more

The smooth shaft of the Stud AN is built from high-strength steel, mechanically galvanised (minimum surface thickness 8 μm) and with ballistic tip. It can be used for Stud Driver AM 35 and AM 60.

Sales units: 200 pcs

Stud AN W25 – Nail with Washer for Powder Actuated Tool

The knurled shaft of the Stud ANS is built from high-strength steel,... more

The knurled shaft of the Stud ANS is built from high-strength steel, mechanically galvanised (minimum surface thickness 8 μm) and with ballistic tip for maximum holding force in steel. It can be used for Stud Driver AM 35 and AM 60.

.

Stud ANC – Nail with Ceiling Bracket for Powder Actuated Tool

The knurled shaft of the Stud ANC is built from high-strength steel,... more

The knurled shaft of the Stud ANC is built from high-strength steel, mechanically galvanised (minimum surface thickness 8 μm) and with ballistic tip for maximum holding force in steel. It can be used for Stud Driver AM 35 and AM 60.

.

Sales units: 200 pcs

Stud ANS – Single Shot Nail for Powder Actuated Tool

The knurled shaft of the Stud ANS is built from high-strength steel,... more

The knurled shaft of the Stud ANS is built from high-strength steel, mechanically galvanised (minimum surface thickness 8 μm) and with ballistic tip for maximum holding force in steel. It can be used for Stud Driver AM 35 and AM 60.

Sales units: 200 pcs

Superbond Resin Capsule RSB

The powerful injection mortar for rebar connections and cracked... more

The powerful injection mortar for rebar connections and cracked concrete.

The Superbond resin capsule RSB is approved for cracked and non-cracked concrete and it is especially economical for individual application and overhead installations.The resin capsule RSB is fast curing, enabling an installation without waiting times and approved processing at frosty temperatures of –30°C. The approval for seismic applications, water filled and diamond drilled holes ensures safety under extreme conditions.

 

 

 
DOWNLOAD PDF – ETA-12/0258 : Superbond Resin Capsule  (2,9 MB)
DOWNLOAD PDF – ICC – ESR 1990: Superbond (0,78 MB)
DOWNLOAD PDF – Safety Data Sheet (0,2 MB)

Threaded Rod Internally: RGMI – Chisel Point

The fixing system with internally threaded anchor for non-cracked... more

The fixing system with internally threaded anchor for non-cracked concrete

Often used for removable or temporary fixings, e.g. for machines. The internally threaded anchor RG MI allows for surface flush removal and reuse of the fixing point, and therefore offers the best possible flexibility. The metric internal thread has an ideal adaptation ability, allowing for the use of standard screws or threaded rods to suit the intended purpose.

 
DOWNLOAD PDF – ETA-12/0258: internally threaded rod (2,6 MB)

 

Threaded Rod: ATR – Galvanised, Chisel Point

The injection system is suitable for prepositioned and push-through... more

The injection system is suitable for prepositioned and push-through installation when combined with threaded rod ATR. The mortar is extruded bubble free from the drill hole base and the mortar bonds the entire surface of the threaded rod with the drill hole wall and seals the drill hole. The threaded rod is set manually, by lightly rotating it until it reaches the drill hole base.

Version: Hot dip galvanized, Grade 5.8

Anchormark Logo

Threaded Rod: RG M – Stainless, Chisel Point

The proven rod anchor for external use with a mortar cartridge or injection... more

The proven rod anchor for external use with a mortar cartridge or injection mortar.

The fischer rod anchor RG M is produced from stainless steel. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in external areas.

Ultracut FBS II – CSK – Concrete Screw, Countersunk Head

The high-performance concrete screw for easy installation. Ultracut provides... more

The high-performance concrete screw for easy installation.

Ultracut provides the best possible flexibility in load and fixture thickness with up to three permitted screw-in depths. The specialized saw tooth geometry allows it to cut quickly into the concrete. No drill hole cleaning is required for mounting in ceilings or floors or when using hollow drill bits with suction. The anchoring is free from expansion pressure (undercut), ensuring the lowest possible axial spacing and edge spacing. ETA approval covers application in cracked concrete, as well as seismic performance categories C1 and C2. Adjustments conforming to the approval makes it possible to loosen the concrete screws 2x, to place materials under and/or align the anchor base plate. National approval regulates multiple uses for temporary anchoring (e.g. formwork construction).

 

         
DOWNLOAD PDF – ETA-Approval-15-0352-Fischer-Ultracut-FBS II (4,1 MB)
DOWNLOAD PDF – Technical Data Sheet – Ultracut-FBS II (0,25 MB)

 

Ultracut FBS II Concrete Screw

The high-performance concrete screw for easy installation. Ultracut provides... more

The high-performance concrete screw for easy installation.

Ultracut provides the best possible flexibility in load and fixture thickness with up to three permitted screw-in depths. The specialized saw tooth geometry allows it to cut quickly into the concrete. No drill hole cleaning is required for mounting in ceilings or floors or when using hollow drill bits with suction. The anchoring is free from expansion pressure (undercut), ensuring the lowest possible axial spacing and edge spacing. ETA approval covers application in cracked concrete, as well as seismic performance categories C1 and C2. Adjustments conforming to the approval makes it possible to loosen the concrete screws 2x, to place materials under and/or align the anchor base plate. National approval regulates multiple uses for temporary anchoring (e.g. formwork construction).

 

         
DOWNLOAD PDF – ETA-Approval-15-0352-Fischer-Ultracut-FBS II (4,1 MB)
DOWNLOAD PDF – Technical Data Sheet – Ultracut-FBS II (0,25 MB)

 

Ultracut FBS II Concrete Screw A4

The high-performance concrete screw for easy installation. The ULTRACUT FBS II... more

The high-performance concrete screw for easy installation.

The ULTRACUT FBS II A4 is designed for push-through installation. The specially hardened red tip provides a faster and more secure installation. It is recommended to use an impact wrench with a suitable impact socket or torx bit. Drill holes do not need to be cleaned during vertical installation (ceiling and floor) or when using a hollow drill. For floor fixing the hole must be drilled 3 x Ø deeper. The ETA approval covers applications in cracked concrete, as well as seismic performance categories C1 and C2. The concrete screw ULTRACUT FBS II A4 offers the possibility for usage in masonry (solid building material).

 

 



 

 
DOWNLOAD PDF – ETA-Approval-ETA-17/0740-Fischer-Ultracut-FBS II-Concrete-Screw (4,1 MB)

Wheel Brushes – Angle Grinder

For finishing solid or hollow rods, porfiles, welded seams, cut edges, gears,... more

For finishing solid or hollow rods, porfiles, welded seams, cut edges, gears, grooves and narrow areas.

Wheel Brushes – Drill

Wheel Brushes for use with a drill are suitable for high-speed drive units and... more

Wheel Brushes for use with a drill are suitable for high-speed drive units and for all common brands thanks to their reinforced components and especially rigid clamping characteristics.

Winchester PAT Charges Cal .27 – Safety Cartridge Strip

Cartridges with 3 different power classes are available for the Power... more

Cartridges with 3 different power classes are available for the Power Drive AM35 Stud Driver. The cartridges can be distinguished by their colour and the power class of the safety cartridges is shown as a number on each cartridge package.

DOWNLOAD PDF – Safety Data Sheet GHS Explosive 1.4  (0,1 MB)

Sales Units: 200 pcs

 

Winchester PAT Disc Charges Cal .25

The Safety Disc Charges for the Power Drive AM60 Stud Driver are available with... more

The Safety Disc Charges for the Power Drive AM60 Stud Driver are available with 3 different power classes. The discs charges can be distinguished by their colour and the power class of the safety discs is shown as a number on each disc package.

 

DOWNLOAD PDF – Safety Data Sheet GHS Explosive 1.4  (0,1 MB)

Sales Units: 100 pcs (10 Discs ) = 10.000 Shot

 

ZYKON Hammerset Anchor FZEA II

The internally threaded anchor with low anchoring depth for individual fixings... more

The internally threaded anchor with low anchoring depth for individual fixings in cracked concrete.

The fischer ZYKON HammerSet anchor FZEA II is suitable for pre-positioned installation. The undercut drill hole is created using the special FZUB drill. Once the anchor has been placed in the drill hole, the expansion sleeve is expanded by the driving in of the internal expansion pin with the FZED Plus setting tool, and the undercut drill hole is filled with a positive fit. The combination of hammerset and ZYKON undercut anchor allows for individual fixings in cracked concrete and the special ZYKON undercut technology reduces the energy required for installation. The FZUB special drill allows for a fast installation by creating the undercut without having to change tools. The embossing that is applied when expanding the anchor secures the simple control of the anchoring.

DOWNLOAD PDF – Approval-ETA 06-0271 HammerSet Anchor ZYKON EA-II (3,6 MB)