Showing all 19 results

Aircrete Anchor GB

Approved safety for aerated concrete. The Aircrete Anchor GB from fischer is... more

Approved safety for aerated concrete.

The Aircrete Anchor GB from fischer is suitable for pre-positioned installation. The self-tapping metal fixing GB taps itself into the plasterboard with a positive fit. The spiral-shaped outer ribs cut a positive fit in the soft building material, thus ensuring the best pressure distribution and load-bearing capacity. The Aircrete Anchor GB can be installed with a hammer – there is no need for special tools, thus saving time and money for the installation.

 

 

Bolt Anchor FAZ II

For highest demands. Powerful and flexible. The FAZ II is suitable for... more

For highest demands. Powerful and flexible.

The FAZ II is suitable for prepositioned and push-through installation and is also ideal for standoff installation thanks to the long thread. The FAZ ll expansion clip enables the highest load bearing capacity, thus fewer fixing points and smaller anchor plates are required. The reduced anchorage depth allows for significantly reduced drill hole depths and thus a noticeably quicker installation. Fewer hammer blows when hammering in the anchor, together with the low torque slippage, ensure a noticeably simple and comfortable setting process

 

 

DOWNLOAD PDF – Approval ETA 05-0069 Bolt Anchor FAZ II (3 MB)
DOWNLOAD PDF – Approval ICC ESR-2948-2020 Bolt Anchor FAZ II (1,0 MB)

Bolt Anchor FBN II

The cost-efficient fixing for flexible use in non-cracked concrete. The FBN II... more

The cost-efficient fixing for flexible use in non-cracked concrete.

The FBN II is suitable for prepositioned and push-through installation; also suitable for stand-off installation under certain conditions. The standard anchorage depth achieves the maximum load-bearing capacities, thus fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This minimizes the amount of time needed for installation whilst increasing flexibility.

 

 
DOWNLOAD PDF – Approval ETA-18/0101 Bolt Anchor FBN II (2,3 MB)

FIS SB 390 S – Superbond Mortar

The concrete all - rounder. Thanks to its high bond strength, Superbond... more

The concrete all – rounder.

Thanks to its high bond strength, Superbond mortar FIS SB achieves a very high load level for safe use in cracked and non-cracked concrete. The Superbond mortar can even be used at extremely high temperatures of up to +150 °C. This opens up new application fields, where no chemical anchor could be used previously. The Superbond mortar FIS SB is approved for seismic applications, which ensures safety even under extreme conditions.

 

 
DOWNLOAD PDF – ETA-12/0258: Superbond mortar FIS SB 390 S (5,5 MB)
DOWNLOAD PDF – ICC – ESR 3572: Superbond mortar FIS SB 390 S (1,8 MB)
DOWNLOAD PDF – GHS Safety Data Sheet FIS SB A (0.5 MB)
DOWNLOAD PDF – GHS Safety Data Sheet FIS SB B (0.5 MB)

Frame Fixing SXR FUS

The all-round solution with short drill hole depth The SXR FUS is suitable... more

The all-round solution with short drill hole depth

The SXR FUS is suitable for push-through installation. The special functioning allows for use in solid and hollow building materials with an anchorage depth of just 50mm, ensuring an economical fixing. The SXR FUS expands in solid building materials and knots in hollow building materials with no impact drilling.

         
DOWNLOAD PDF – ETA-Approval-07-0121 Fischer Frame Fixing (5,1 MB)

Frame Fixing SXR T

The all-round solution with short drill hole depth The SXR is suitable for... more

The all-round solution with short drill hole depth

The SXR is suitable for push-through installation. The special functioning allows for use in solid and hollow building materials with an anchorage depth of just 50mm, ensuring an economical fixing. The SXR expands in solid building materials and knots in hollow building materials with no impact drilling.

         
DOWNLOAD PDF – ETA-Approval-07-0121 Fischer Frame Fixing (5,1 MB)

High Performance Anchor FH II CSK

The push-through anchor for fixings with sophisticated design in cracked... more

The push-through anchor for fixings with sophisticated design in cracked concrete.

The anchor construction allows for wide-ranging head shapes for fixing points with sophisticated design. The ideal interaction of screw shank and sleeve allows for a high shear load, thus fewer fixing points are required. The international approvals guarantee maximum safety and the best performance. These approvals even cover use in earthquake zones (seismic). The optimized geometry reduces the energy required for installation.

 

         
DOWNLOAD PDF – Approval ETA 07-0025 High Performance Anchor FH II (3,8 MB)
DOWNLOAD PDF – Approval ICC High-performance-anchor-FH-II (0,9 MB)

High Performance Anchor FH II S

The push-through anchor for fixings with sophisticated design in cracked... more

The push-through anchor for fixings with sophisticated design in cracked concrete

The anchor construction allows for wide-ranging head shapes for fixing points with sophisticated design. The ideal interaction of screw shank and sleeve allows for a high shear load, thus fewer fixing points are required. The international approvals guarantee maximum safety and the best performance. These approvals even cover use in earthquake zones (seismic). The optimized geometry reduces the energy required for installation.

         
DOWNLOAD PDF – Approval ETA 07-0025 High Performance Anchor FH II (3,7 MB)
DOWNLOAD PDF – Approval ICC High Performance Anchor FH II (0,9 MB)

 

Superbond Resin Capsule RSB

The powerful injection mortar for rebar connections and cracked... more

The powerful injection mortar for rebar connections and cracked concrete.

The Superbond resin capsule RSB is approved for cracked and non-cracked concrete and it is especially economical for individual application and overhead installations.The resin capsule RSB is fast curing, enabling an installation without waiting times and approved processing at frosty temperatures of –30°C. The approval for seismic applications, water filled and diamond drilled holes ensures safety under extreme conditions.

 

 

 
DOWNLOAD PDF – ETA-12/0258 : Superbond Resin Capsule  (2,9 MB)
DOWNLOAD PDF – ICC – ESR 1990: Superbond (0,78 MB)
DOWNLOAD PDF – Safety Data Sheet (0,2 MB)

Threaded Rod Internally: RGMI – Chisel Point

The fixing system with internally threaded anchor for non-cracked... more

The fixing system with internally threaded anchor for non-cracked concrete

Often used for removable or temporary fixings, e.g. for machines. The internally threaded anchor RG MI allows for surface flush removal and reuse of the fixing point, and therefore offers the best possible flexibility. The metric internal thread has an ideal adaptation ability, allowing for the use of standard screws or threaded rods to suit the intended purpose.

 
DOWNLOAD PDF – ETA-12/0258: internally threaded rod (2,6 MB)

 

Threaded Rod: ATR – Galvanised, Chisel Point

The injection system is suitable for prepositioned and push-through... more

The injection system is suitable for prepositioned and push-through installation when combined with threaded rod ATR. The mortar is extruded bubble free from the drill hole base and the mortar bonds the entire surface of the threaded rod with the drill hole wall and seals the drill hole. The threaded rod is set manually, by lightly rotating it until it reaches the drill hole base.

Version: Hot dip galvanized, Grade 5.8

Anchormark Logo

Threaded Rod: RG M – Stainless, Chisel Point

The proven rod anchor for external use with a mortar cartridge or injection... more

The proven rod anchor for external use with a mortar cartridge or injection mortar.

The fischer rod anchor RG M is produced from stainless steel. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in external areas.

Ultracut FBS II – CSK – Concrete Screw, Countersunk Head

The high-performance concrete screw for easy installation. Ultracut provides... more

The high-performance concrete screw for easy installation.

Ultracut provides the best possible flexibility in load and fixture thickness with up to three permitted screw-in depths. The specialized saw tooth geometry allows it to cut quickly into the concrete. No drill hole cleaning is required for mounting in ceilings or floors or when using hollow drill bits with suction. The anchoring is free from expansion pressure (undercut), ensuring the lowest possible axial spacing and edge spacing. ETA approval covers application in cracked concrete, as well as seismic performance categories C1 and C2. Adjustments conforming to the approval makes it possible to loosen the concrete screws 2x, to place materials under and/or align the anchor base plate. National approval regulates multiple uses for temporary anchoring (e.g. formwork construction).

 

         
DOWNLOAD PDF – ETA-Approval-15-0352-Fischer-Ultracut-FBS II (4,1 MB)
DOWNLOAD PDF – Technical Data Sheet – Ultracut-FBS II (0,25 MB)

 

Ultracut FBS II Concrete Screw

The high-performance concrete screw for easy installation. Ultracut provides... more

The high-performance concrete screw for easy installation.

Ultracut provides the best possible flexibility in load and fixture thickness with up to three permitted screw-in depths. The specialized saw tooth geometry allows it to cut quickly into the concrete. No drill hole cleaning is required for mounting in ceilings or floors or when using hollow drill bits with suction. The anchoring is free from expansion pressure (undercut), ensuring the lowest possible axial spacing and edge spacing. ETA approval covers application in cracked concrete, as well as seismic performance categories C1 and C2. Adjustments conforming to the approval makes it possible to loosen the concrete screws 2x, to place materials under and/or align the anchor base plate. National approval regulates multiple uses for temporary anchoring (e.g. formwork construction).

 

         
DOWNLOAD PDF – ETA-Approval-15-0352-Fischer-Ultracut-FBS II (4,1 MB)
DOWNLOAD PDF – Technical Data Sheet – Ultracut-FBS II (0,25 MB)

 

Ultracut FBS II Concrete Screw A4

The high-performance concrete screw for easy installation. The ULTRACUT FBS II... more

The high-performance concrete screw for easy installation.

The ULTRACUT FBS II A4 is designed for push-through installation. The specially hardened red tip provides a faster and more secure installation. It is recommended to use an impact wrench with a suitable impact socket or torx bit. Drill holes do not need to be cleaned during vertical installation (ceiling and floor) or when using a hollow drill. For floor fixing the hole must be drilled 3 x Ø deeper. The ETA approval covers applications in cracked concrete, as well as seismic performance categories C1 and C2. The concrete screw ULTRACUT FBS II A4 offers the possibility for usage in masonry (solid building material).

 

 



 

 
DOWNLOAD PDF – ETA-Approval-ETA-17/0740-Fischer-Ultracut-FBS II-Concrete-Screw (4,1 MB)

FTC Zinc Alu Spray – 400 ml

Ideal for repairing damaged zinc coatings using colour matching corrosion... more

Ideal for repairing damaged zinc coatings using colour matching corrosion protection.

Zinc Alu Spray enables a subtle repair to damaged hot-dip galvanised areas thanks to its colour matching with the hot-dip galvanisation. Thanks to the excellent holding properties on bare metal, it guarantees a lasting connection to the base material. The fast-drying Zinc Alu Spray guarantees good, weatherproof corrosion protection and, as such, is suitable for use both indoors and out.

  • For all iron and steel surfaces
  • Hot-dip galvanised surfaces following drilling, ironwork or welding
  • Non-ferrous heavy metal

 

DOWNLOAD PDF – GHS Safety Data Sheet: FTC Zinc Alu Spray 4.0 (0,3 MB)

FTC-ZS Zinc Spray – 400 ml

Fast-drying surface and corrosion protection with outstanding long-term effect... more

Fast-drying surface and corrosion protection with outstanding long-term effect for metals.

The FTC Zinc Spray are useful for all kind of metals that need corrosion protection and is perfect for the coating of drilling and cutting points as well as welded joints. The surface is dust-dry after just approx. 8 minutes and it is fully hardened within 24 hours. The FTC Zinc Spray have excellent corrosion protection with long-term effect and a heat-resistant up to approx. 500°C.

 

Sales Units: 12 pcs

DOWNLOAD PDF – GHS Safety Data Sheet: FTC-ZS Zinc Spray 5.0 (0,7 MB)