Steel Anchoring – main category

Showing all 17 results

Threaded Rod Internally: RGMI – Chisel Point

The fixing system with internally threaded anchor for non-cracked... more

The fixing system with internally threaded anchor for non-cracked concrete

Often used for removable or temporary fixings, e.g. for machines. The internally threaded anchor RG MI allows for surface flush removal and reuse of the fixing point, and therefore offers the best possible flexibility. The metric internal thread has an ideal adaptation ability, allowing for the use of standard screws or threaded rods to suit the intended purpose.

 

 

 

DOWNLOAD PDF – ETA-12/0258: internally threaded rod (3 MB)

 

Bolt Anchor FBN II

The cost-efficient fixing for flexible use in non-cracked concrete. The FBN II... more

The cost-efficient fixing for flexible use in non-cracked concrete.

The FBN II is suitable for prepositioned and push-through installation; also suitable for stand-off installation under certain conditions. The standard anchorage depth achieves the maximum load-bearing capacities, thus fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This minimizes the amount of time needed for installation whilst increasing flexibility.

 

 
DOWNLOAD PDF – Approval ETA-07/0211 Bolt Anchor FBN II (1,7 MB)
DOWNLOAD PDF – Approval ETA-18/0101 Bolt Anchor FBN II (2,3 MB)

Internally Threaded Ruspert® – Concrete Screws

This screws offers unlimited application possibilities. It is usable without... more

This screws offers unlimited application possibilities. It is usable without special tools only with an impact wrench. It is simple and fast to use. No special tools are required. The RUSPERT® coating provides excellent corrosion protection.

The internally threaded concrete screw gets driven into the drill hole with an impact wrench.

For the use in concrete (non-safety relevant applications).

Bolt Anchor FAZ II

For highest demands. Powerful and flexible. The FAZ II is suitable for... more

For highest demands. Powerful and flexible.

The FAZ II is suitable for prepositioned and push-through installation and is also ideal for standoff installation thanks to the long thread. The FAZ ll expansion clip enables the highest load bearing capacity, thus fewer fixing points and smaller anchor plates are required. The reduced anchorage depth allows for significantly reduced drill hole depths and thus a noticeably quicker installation. Fewer hammer blows when hammering in the anchor, together with the low torque slippage, ensure a noticeably simple and comfortable setting process

 

 

 

DOWNLOAD PDF – ETA 05-0069 Bolt Anchor FAZ II 04/20 (1,1 MB)
DOWNLOAD PDF – ICC ESR-2948-2020 Bolt Anchor FAZ II (0,9 MB)

High Performance Anchor FH II S

The push-through anchor for fixings with sophisticated design in cracked... more

The push-through anchor for fixings with sophisticated design in cracked concrete

The anchor construction allows for wide-ranging head shapes for fixing points with sophisticated design. The ideal interaction of screw shank and sleeve allows for a high shear load, thus fewer fixing points are required. The international approvals guarantee maximum safety and the best performance. These approvals even cover use in earthquake zones (seismic). The optimized geometry reduces the energy required for installation.

 

 

 

 
DOWNLOAD PDF – Approval ETA 07-0025 High Performance Anchor FH II 08/18 (4,3 MB)
DOWNLOAD PDF – Approval ICC High Performance Anchor FH II (2,1 MB)

 

AM Premium Concrete Screw

High end, powerful screw solution for fast and simple installation. The AM... more

High end, powerful screw solution for fast and simple installation.

The AM Premium Concrete Screws are simple and time-saving threaded screws for the use in concrete and the RUSPERT® coating provides excellent corrosion protection. Once screwed into the hole the thread taps into concrete for positive fit anchorage. The concrete screw are completely removable anchor suitable for temporary fixings and virtually expansion-free operation allows cost-efficient fixing with small axial spaces and edge distances.

Anchormark Logo

 

Premium Concrete Screws with Rusper® Coating from Anchormark

  
DOWNLOAD PDF – ETA-15-0905 Premium Concrete-Screw AM (0,9 MB)

Nail Anchor FNA II – with Ring

The installation-friendly hammerset anchor for multiple fixings. The FNA II... more

The installation-friendly hammerset anchor for multiple fixings.

The FNA II with nail head is suitable for push-through installation. The special active principle allows for a simple hammerset installation and therefore, a short processing time. The extremely short anchor depth prevents reinforcement hits and creates the conditions for a trouble-free installation. The optimised expansion clip prevents it from falling out during overhead installations. The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety.

 

 

DOWNLOAD PDF – Approval ETA 06-0175 Nail Anchor FNA II (1,9 MB)

HammerSet Anchor EA II

The internally threaded anchor with rim for simple hammerset installation The... more

The internally threaded anchor with rim for simple hammerset installation

The Hammerset EA II is suitable for pre-positioned installation. The sleeve is then expanded against the drill hole wall by driving in the internal bolt with the EAW H Plus setting tool (alternative: EA II-SDS machine setting tool). The embossed rim prevents the anchor sleeve from slipping, thus ensuring a trouble-free hammers installation. The metric internal thread has an ideal adaptation ability, allowing for the use of standard screws or threaded rods to suit the intended purpose.

DOWNLOAD PDF – Approval-ETA 07-0135 HammerSet Anchor EA-II (2,2 MB)

Nail Anchor FNA II – with Nail Head

The installation-friendly hammerset anchor for multiple fixings. The FNA II... more

The installation-friendly hammerset anchor for multiple fixings.

The FNA II with nail head is suitable for push-through installation. The special active principle allows for a simple hammerset installation and therefore, a short processing time. The extremely short anchor depth prevents reinforcement hits and creates the conditions for a trouble-free installation. The optimised expansion clip prevents it from falling out during overhead installations. The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety.

 

 

​

DOWNLOAD PDF – Approval ETA 06-0175 Nail Anchor FNA II (1,9 MB)

ZYKON Hammerset Anchor FZEA II

The internally threaded anchor with low anchoring depth for individual fixings... more

The internally threaded anchor with low anchoring depth for individual fixings in cracked concrete.

The fischer ZYKON HammerSet anchor FZEA II is suitable for pre-positioned installation. The undercut drill hole is created using the special FZUB drill. Once the anchor has been placed in the drill hole, the expansion sleeve is expanded by the driving in of the internal expansion pin with the FZED Plus setting tool, and the undercut drill hole is filled with a positive fit. The combination of hammerset and ZYKON undercut anchor allows for individual fixings in cracked concrete and the special ZYKON undercut technology reduces the energy required for installation. The FZUB special drill allows for a fast installation by creating the undercut without having to change tools. The embossing that is applied when expanding the anchor secures the simple control of the anchoring.

DOWNLOAD PDF – Approval-ETA 06-0271 HammerSet Anchor ZYKON EA-II (3,6 MB)

Ultracut FBS II Concrete Screw

The high-performance concrete screw for easy installation. Ultracut provides... more

The high-performance concrete screw for easy installation.

Ultracut provides the best possible flexibility in load and fixture thickness with up to three permitted screw-in depths. The specialized saw tooth geometry allows it to cut quickly into the concrete. No drill hole cleaning is required for mounting in ceilings or floors or when using hollow drill bits with suction. The anchoring is free from expansion pressure (undercut), ensuring the lowest possible axial spacing and edge spacing. ETA approval covers application in cracked concrete, as well as seismic performance categories C1 and C2. Adjustments conforming to the approval makes it possible to loosen the concrete screws 2x, to place materials under and/or align the anchor base plate. National approval regulates multiple uses for temporary anchoring (e.g. formwork construction).

 

 

     
DOWNLOAD PDF – ETA 15-0352 Fischer Ultracut FBS II 04/20 (5,8 MB)
DOWNLOAD PDF – Technical Data Sheet – Ultracut-FBS II (1 MB)

Threaded Rod: ATR – Galvanised, Chisel Point

The injection system is suitable for prepositioned and push-through... more

The injection system is suitable for prepositioned and push-through installation when combined with threaded rod ATR. The mortar is extruded bubble free from the drill hole base and the mortar bonds the entire surface of the threaded rod with the drill hole wall and seals the drill hole. The threaded rod is set manually, by lightly rotating it until it reaches the drill hole base.

Version: Hot dip galvanized, Grade 5.8

Anchormark Logo

Setting Tool EAW H Plus for HammerSet EA II

Highest safety through perfect expansioning of the anchor. Manual setting tool... more

Highest safety through perfect expansioning of the anchor.

Manual setting tool with hand impact protection for fixing Fischer Hammerset anchors EA II M10. The manual setting tool is build with ergonomic plastic to handle and hand impact protection for quick, safe fixing of Fischer Hammerset anchors EA II.

 

Ultracut FBS II Concrete Screw A4

The high-performance concrete screw for easy installation. The ULTRACUT FBS II... more

The high-performance concrete screw for easy installation.

The ULTRACUT FBS II A4 is designed for push-through installation. The specially hardened red tip provides a faster and more secure installation. It is recommended to use an impact wrench with a suitable impact socket or torx bit. Drill holes do not need to be cleaned during vertical installation (ceiling and floor) or when using a hollow drill. For floor fixing the hole must be drilled 3 x Ø deeper. The ETA approval covers applications in cracked concrete, as well as seismic performance categories C1 and C2. The concrete screw ULTRACUT FBS II A4 offers the possibility for usage in masonry (solid building material).

 

 

 

 

 
DOWNLOAD PDF – ETA-Approval-ETA-17/0740-Fischer-Ultracut-FBS II-Concrete-Screw (4,1 MB)
DOWNLOAD PDF – Technical Data Sheet – Ultracut FBS II A4 (0,7 MB)

Threaded Rod: RG M – Stainless, Chisel Point

The proven rod anchor for external use with a mortar cartridge or injection... more

The proven rod anchor for external use with a mortar cartridge or injection mortar.

The fischer rod anchor RG M is produced from stainless steel. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in external areas.

High Performance Anchor FH II CSK

The push-through anchor for fixings with sophisticated design in cracked... more

The push-through anchor for fixings with sophisticated design in cracked concrete.

The anchor construction allows for wide-ranging head shapes for fixing points with sophisticated design. The ideal interaction of screw shank and sleeve allows for a high shear load, thus fewer fixing points are required. The international approvals guarantee maximum safety and the best performance. These approvals even cover use in earthquake zones (seismic). The optimized geometry reduces the energy required for installation.

 

 

 
DOWNLOAD PDF – Approval ETA 07-0025 High Performance Anchor FH II 08/18 (4,3 MB)
DOWNLOAD PDF – Approval ICC High-performance-anchor-FH-II (2,1 MB)